Fashion: Fastener: Button
Irregular fastener spacing   (0)  [vote for, against]
Non-uniform distribution of fasteners on fabric openings

When doing up the poppers at the bottom of a duvet or when doing up a small child's clothing, it's so easy to encounter the "out by one" error, where you have fastened popper 1 to popper 2, popper 2 to popper 3 and so on. You then have to undo all the poppers and start again.
This could easily be solved by adopting non-uniform spacing. So for example, the distance between popper 1 and popper 2 could be 6 inches; Between 2 and 3, 7 inches; Between 3 and 4, 5 inches, etc. It would then be obvious as soon as you had gone wrong, resulting in a saving in time of months probably, factored over the average lifetime of making fastener errors on duvets, shirts, coats, baby's clothes, etc.
-- hippo, Jan 09 2003

Sounds workable. The aesthetics of the uneven spacing might drive some people nuts. In the case of "poppers" (snaps), it seems like it would be helpful if adjacent fasteners were mechanically incompatible e.g. two different sizes.
-- half, Jan 09 2003


Might work - a sequence like ... popper - button - velcro - popper - button - velcro... would reduce errors.
-- hippo, Jan 09 2003


shame there is no way to move them up and down on a track kind of arrangement.
-- po, Jan 09 2003


thinking how you could insert magnets so that they repel the popper above or below.
-- po, Jan 09 2003


Dash! Daydreaming and got the *#@! zipper caught!
-- reensure, Jan 09 2003


Nice ones po! On a track and magnets - both rockin' ideas. Especially the magnets.
-- Matty, Jan 09 2003


Some cunning use of magnets would be good, as would making alternate pairs of poppers out of matter and antimatter.
-- hippo, Jan 10 2003


[Rods] - see my Jan 9 anno
-- hippo, Jan 10 2003


...or just have the first few at the end in a little group -- just where you need them to be stronger.

Lets face it, we've all got a different idea of how to do the fine detail. That doesn't take away from the fact that this is a very fine idea. King size croissant with popstuds (irregularly spaced).
-- st3f, Jan 10 2003


Why not just alternate the "mates" for each side of the item to be fastened? For example, the left side, instead of being all buttons, would alternate buttons and buttonholes. The right side would alternate buttons and buttonholes, but off-set by one so that each pair would match.

The same could be done with poppers, hooks and loops, velcro, etc. This way, you get to keep the regular spacing between fasteners and the consistent look of the same fastening system.
-- kirby, Jan 10 2003


But if the right side is on top, then every other fastener would be a button on its back side - difficult to button/unbutton inwards.
-- FarmerJohn, Jan 10 2003


I am thinking of the poor chaps who are sewing this stuff, but I like the alternate idea, would be best if used snaps or velcro thogh, buttons would be difficult.
-- spbeaucham, Jan 10 2003


[FJ]: whoops, I guess I didn't think that button scheme all the way through. It *would* work with poppers/snaps and hooks & loops, though.
-- kirby, Jan 13 2003


i like [kirby]'s idea best. if the snaps were magnitized, the article of clothing would effect anything metalic nearby (imagine being near a box of paper clips... not a pretty picture). pair numbers would ruin the clothes, as would a sequence (velcro, buttons, snaps, popper.. ect). you have to keep your sense of style here. if the snaps (or whatever) kept switching sides the problem would be eliminated. i doubt anyone would mismatch by 2 spaces...
-- PandaBear, Jan 13 2003



random, halfbakery