h a l f b a k e r y
"Look on my works, ye Mighty, and despair!"
add, search, annotate, link, view, overview, recent, by name, random
news, help, about, links, report a problem
or get an account
Please log in.
Before you can vote, you need to register.
Please log in or create an account.
Lots of machines small and large have screw-attached
covers (such as battery compartment covers) that need to
be removed and replaced often. Annoyingly, this requires
an appropriate screwdriver or screwdriver surrogate.
For machines where strength isnt a factor (this idea was
a battery-powered cat toy of mine that requires
a rechargeable AA battery swapout about once a week), I
propose an assortment of screw-replacing corrugated
plastic fasteners that can simply be stuck into the
screwholes, with an assortment of easy-to-pull flexible
tabs and rigid nobs extending their heads. Removal and
reinsertion time is reduced from minutes (including the
time needed to find a screwdriver/screwdriver surrogate)
to seconds. Stripping of threads and screwheads is
Could be packaged in blister-packs and sold in hardware,
grocery, and specialty (eg: pet) store checkout displays.
Better patent it (or license and existing patent) quickly
this could be my route to entrepreneurial easy street!
Body clips ([bs Orthodox Union]'s post)
Sounds like you want a smaller version of these [pashute, May 14 2015]
[bs0u0155, May 14 2015]
[bs0u0155, May 14 2015]
||This is not an entirely bad idea.
||However, when you say "corrugated" - you mean the
surrogate screw just has a (pardon the expression)
shaft, sort of like the original screw thread, but
be pulled out and pushed in? If so, it's going to wear.
||However, if the plastic widget starts
out as a slightly-tapered smooth-sided plug, it could
screwed into the hole. Doing so would carve a set of
into the surface, turning it into a plastic screw, which
then be unscrewed and rescrewed using the tab.
||There might be a market for this. I can see it being
also, as a replacement for lost screws. You'd need to
them as a pack containing a range of diameters - just
whichever is slightly bigger than the original screw,
||Change from: Where did I put that pesky screwdriver...?
||to: Where did I put that pesky blister-pack...?
||I'd get lots of lawsuit insurance for when the children ate the lithium, nicad, or lkaline batteries.
||// Anything like [link] ? //
Yes, but where most plastic fastener, like those in the
link are meant to inserted 1 time only, hold strongly, and
have an inconspicuous, low-profile head, the ideas are
meant to be inserted and removed many times, hold no
more strongly than the users finger grip can overcome,
and have an easy-to-grab head.
// you mean the surrogate screw just has a (pardon the
expression) ribbed shaft, sort of like the original screw
thread, but designed to be pulled out and pushed in? If
so, it's going to wear. //
The ribbed surrogate screw should last a hundred or so
remove-insert cycles 2+ years of weekly uses. It
shouldnt damage what it screws into, which may be a
cheap plastic case (such as is the case with my cat toy).
||Another way to look at the idea is that its an easy way
to upgrade an inconvenient screw-on hatch with a
convenient finger-latch one, such as those found on
better designed devices. In a more perfect world,
thered be no need them, because all hatches would be
near perfectly designed.
||People with diminished vision and fine motor control,
such as older people, are a target market. No more will
they need to pester younger friends, neighbors, and
relatives to change the batteries in their poorly-designed
||In addition to my kitties battery-hungry toy, an
inspiration for this idea is the engine cover shell of my
small electric lawn mower. Occasionally, this otherwise
reliable tool throws its drive belt, requiring 4 1.5 screws
to be backed out then screwed back in, a minutes-long
task with a manual screwdriver, or minutes to fetch and
use an electric one. Over the years, the screw heads are
become gradually worn to near unusability.
||Hmm, the world of radio controlled cars hasn't taught me
much, but, there are such things as body clips. They work by
replacing the screw with a threaded post. A thin hex section
is used to drive it in. Protruding from the hex section is a
post, this will penetrate through the flat hatch or whatever
you are trying to secure, then, you put a spring clip through
holes in the post and everything is held securely. It's also
how race cars hold their bonnet/hoods down, takes 2
seconds to remove them. Would work well for the mower.
||Clearly state the difference(s) between this and [link] and
add a drawing.
||pash, not quite, some of these <link> holding on a body by
sliding through the posts as highlighted <link>. What isn't
shown well is that the clips have a bump perpendicular to
the main springy axis, meaning that they can exert spring
pressure downward too.
||What's wrong with Cleco fasteners? We use those on some of our drill jigs at work in place of screws. They go right in the existing screw hole.
||I just took a faucet apart to replace a plastic valve. They used steel screws, now a pile of rust; needed to be drilled out.