Half a croissant, on a plate, with a sign in front of it saying '50c'
h a l f b a k e r y
(Serving suggestion.)

idea: add, search, annotate, link, view, overview, recent, by name, random

meta: news, help, about, links, report a problem

account: browse anonymously, or get an account and write.

user:
pass:
register,


             

Please log in.
Before you can vote, you need to register. Please log in or create an account.

Sprocketbox

Revisiting the Frazer-Nash "Chain Gang"
  (+6)
(+6)
  [vote for,
against]

The Frazer-Nash “Chain Gang” sports car of the ‘20’s and ‘30’s was a surprisingly effective device. For those of you who are not familiar with it, this was a light and Spartan British sports car very much in the Vintage mould, which featured a singular system of chain-drive transmission. Drive was taken from the clutch, via a primary drive shaft, to a bevel box and cross-shaft just aft of the driver’s seat. Several sets of exposed sprockets and chains, each engageable as required by a dog clutch, connected this shaft directly to the rear axle. The arrangement was light, simple, easy to repair and modify, and capable of handling considerable amounts of torque.

However, simplicity was taken to the point of dispensing with a differential, an attempt to mitigate the effect of that omission being made in the form of a relatively narrow rear track. To some extent the rear-axle-induced understeer that nevertheless resulted was compensated by the oversteer-inducing extreme of rear roll stiffness, which was just as well as what roll movement there was put torsional loads on the chains and thus considerably shortened their lives. Chains did break from time to time, but they were repaired, because the “Chain Gang” was that sort of car. All in all they did what they were supposed to do extremely well, and a small minority continue to swear by them to this day.

While it is neither necessary or desirable to render the transmission system of a rough-and-ready Vintage-style sports car completely maintenance-free, it is certainly possible to improve the system to eliminate the major shortcomings. To this end I propose: 1. incorporating a differential concentric with the rear sprocket set and 2. mounting the rear shaft to the chassis by bearings and using an independent or DeDion rear suspension. The system may readily be assembled today, using a crown-wheel-and-pinion set out of a conventional rear axle, a collection of motorcycle chains, and the differential out of the aforementioned axle. The most difficult part would be making up the dog-clutch units. Most practical would be back-to-back units that each serve two sprockets, which would allow a conventional gated shift pattern. It is also entirely possible for these to be narrow enough to allow only a flat-bar reaction arm and shift arm between adjacent chains, to keep the entire system more or less within the width of a conventional rearend third member.

The process of calculating the torque capacity and physical size of the system gave rise to a few further ideas and observations. The torque capacity of the system is proportional to the size of the sprockets and the strength of the chains. The greatest capacity is required of the first-speed set; chains for the other speeds may be progressively lighter, provided the driven sprockets are the same size. This has also the advantage that all the dog-clutch/sprocket-pair assemblies in the system would be the same. Taking, for example, a seven-speed arrangement with a 3.89:1 primary reduction, a 3.28:1 first gear ratio, and 3.66”/12” (91mm/300mm) sprockets gives a torque capacity of around 300lb.ft using common high-performance motorcycle chain, or over three times as much using certain types of racing chain. Reducing the sprocket sizes reduces the torque capacity correspondingly.

It makes sense to mount the dog-clutch assemblies on the driven shaft, as running them on the driving shaft would cause overspeeding of the lower-speed chains when cruising at speed. The only exception would be (in the above example) the 6th/7th dog-clutch unit, if 7th is an overdrive ratio. Mounting this on the driving shaft would allow the 7th speed driven sprocket to be smaller than the other driven sprockets. If the dog-clutch units are identical they can also be swopped about in the system as they wear: the 2nd/3rd unit will see the most wear, and may therefore see duty as the 4th/5th, 6th/7th, and 1st/reverse units before finally being reconditioned. That way only that which is worn out needs to be reconditioned.

Ned_Ludd, Feb 15 2008

[link]






       The more I read it, the better I like it.   

       If you don't restrict yourself to just motorcycle chain, power capacities go through the roof. There're other roller chains out there, granted probably not as quiet, that would work pretty well at this.   

       I do get the vibe that this might have more rotating mass than a typical tranny; could it obviate the need for the usual heavy flywheel?
elhigh, Feb 15 2008
  

       What is the advantage of chain/sprockets over gear/gear connections? I get the whole dog clutch system, though as the past owner of a Mercruiser Alpha1 outdrive on a boat, I don't like dog clutches.
MisterQED, Feb 15 2008
  

       I am a big proponent of light weight, safe, enclosed mini vehicles. I think they hold good potential to help solve both our energy problems and our traffic congestion problems. The British, during WWII had a little car, I can't recall the name of it...that only had a ten hp engine...and it was quite zippy. Properly applied engine power in properly weighted and transmissioned vehicles can be very efficient. I think, aslo, the chain drive has proven itself since practically the beginning of motorized transportation....don't forget the first heavy trucks had chain drives. And, motorcycles are well proven as light weight chain driven (or partically transmissioned)transporters.   

       Some old steam powered launches used a chain drive and pulley system....and I saw one boat when I was a kid that was a five car ferry that used chain drive side paddles. When the chain drives are combined with simple geared speed reducers it can result in a very efficient transmission.   

       I like this idea even though I did not quite understand all the description...I think I have the gist of it.
Blisterbob, Feb 15 2008
  

       The transmission in my car was made by idiots. Not even very smart idiots. I have frequently considered removing it and replacing it with one of my own design. I have been contemplating chain drive, but kept thinking that if it was a good idea, it would be done already. Your idea gives me the confidence to explore this possibility, and ask: What are the downsides?
bonus: i work for the sister company of a major gear and chain manuf. i have access to every imaginable type of gear, sprocket, cog, chain, bearing, etc.
ericscottf, Feb 15 2008
  

       My God! Eric...do it! what a golden opportunity. Keep us posted as to how it works out.
Blisterbob, Feb 15 2008
  

       To answer an earlier question: Chain vs gears; the chain spreads load across several teeth of the sprocket, making for a lighter sprocket. Conversley, each link of the chain must be able to take the full load.   

       Driving the rear axle directly is not the best use of the system as each chain must take the full torque at axle speed. It makes more sense to run the chains or gears at engine speed and use a single final reduction to carry the high torque. As speeds get higher, chains begin to have problems with resonance and centripetal force, not to mention lubrication. The chain and sprocket shifter (also used by Morgan, who avoided the differential issue by using a single rear wheel) is a simple, cheap solution for a low volume manufacturer. For performance and durability, you can't beat a properly designed and assembled gearbox.
Twizz, Mar 31 2009
  
      
[annotate]
  


 

back: main index

business  computer  culture  fashion  food  halfbakery  home  other  product  public  science  sport  vehicle